MaxxTow Adjustable-Height Ball Mount Review - 2013 Jeep Wrangler- Video
Today on our 2013 Jeep Wrangler we'll be test fitting the MaxxTow adjustable height ball mount for two inch hitches with a ten inch drop or eight inch rise rated at 5,000 pounds, part number MT70067. Before we begin our test fit, we'll first need to obtain the hitch height of our vehicle. This is the measurement from the ground to the inside top of the receiver tube. The hitch height for this vehicle is about nineteen and three-quarters of an inch. Keep in mind that this measurement may vary due to tire size, hitch style or other after market accessories. We'll now begin our test fit in the drop position by sliding the shank of the ball mount into the opening of the hitch and securing it with a pin and clip. We then can lower the ball mount platform into its lowest position by pulling the two clips and readjusting the pins. With the ball mount platform in it's lowest position with the ball mount in a drop position, we can measure from the ground to the top of the ball platform and we'll get a measurement of about ten inches. We can now put the ball mount platform in its highest position with the ball mount sill in the drop. more
9/25/2013 1:52:16 PM
Draw-Tite Ball Mount Review - 2013 Jeep Wrangler- Video
Today on our 2013 Jeep Wrangler, we'll be test fitting the Draw-Tite ball mount with a3/4 inch rise or a 2 inch drop, rated at 7500 pounds, part number 2923. Before we begin our test fit, we'll first need to obtain the hitch height of our vehicle. This is the measurement from the ground to the inside top of the of the receiver tube. The hitch height for this vehicle is about 19 and 3/4's of an inch. Keep in mind that this measurement may vary due to tire size, hitch style, or other aftermarketaccessories. We'll now go ahead and begin our test fit by sliding the shank of the ball mount in the drop position in to the receiver tube of our hitch. We can then secure it with a pin and a clip. We can then measure from the ground to the top of the ball platform, getting a measurement of about 17 and 1/2 inches. Now if your vehicle's hitch height matches ours, and your trailer's ride height matches this measurement, this should be an appropriate ball mount for you. We can then flip the ball mount over to the rise position, and again, measure from the ground to the top of the ball platform. more
9/25/2013 1:50:49 PM
Curt Tri-Ball Mount Review - 2013 Jeep Wrangler- Video
Today on our 2013 Jeep Wrangler, we'll be test fitting the Curt Tri Ball Mount for 2inch hitches, part number C45001. Before we begin our test fit, we'll first need to obtain the hitch height of our vehicle. This is the measurement from the ground to the inside top of the receiver tube. The hitch height for this vehicle is about 19 and 3/4's of an inch. Keep in mind that this measurement may vary due to tire size, hitch style, or other aftermarket accessories. We'll begin our test fit by sliding the shank of the ball mount in to the opening of the hitch, and securing it with a pin and clip. Now since this ball mount has no drop or rise, if your vehicle's hitch height matches your trailer's ride height, this ball mount would be appropriate for you. You can also flip the ball mount over to the left to access the 2 inch ball, or you can flip it over to the right to access the 1 and 7/8's inch ball. This ball mount is a great way for you to carry multiple size trailers without needing to purchase additional ball mounts. And that will complete today's test fit for the Curt Tri Ball Mount for 2 inch hitches, part number C45001 on our 2013 Jeep Wrangler. more
9/25/2013 1:50:39 PM
Convert-A-Ball 6-Way Multi-Hitch Ball Mount Review - 2013 Jeep Wrangler- Video
Today on our 2013 Jeep Wrangler, well be test fitting the Convert-A-Ball Cushion 6-Way Multi Hitch Ball Mount for 2 inch hitches, rated at 10,000 pounds, part number CAB-6W. Well begin our test fit by sliding the shank of the ball mount into the opening of the hitch and securing it with the pin and clip. Now since this ball mount has no drop or rise, if your vehicles hitch height matches your trailers ride height, this ball mount would be appropriate for you. Now with the ball mount on this position, you can access the 2-5/16 of an inch ball at the top. We can now rotate the ball mount to the left or to the right to access the either 1-7/8 inch ball or the 2 inch ball. Now if you flip it over toward the pin and at the top portion of the ball mount, you can see that once we remove this over clip, the pin cannot be removed from the ball mount. Therefore it can only be used at the bottom of the ball mount. more
9/25/2013 1:48:46 PM
Convert-A-Ball Dual-Cushioned Adjustable Ball Mount Review - 2013 Jeep Wrangler- Video
Today on our 2013 Jeep Wrangler well be test fitting the Convert-a-ball dual cushion adjustable ball mount with a seven inch rise, two and nine inch drop rated at 5,000lbs part #: CAB-UM. Before we begin our test fit well first need to obtain the hitch height of our vehicle. This is the measurement from the ground to the inside top of the receiver tube. The hitch height for this vehicle is about 19 and three quarters of an inch. Keep in mind that this measurement may vary due to tire size, hitch style or other after-market accessories. Well begin our test fit in the drop position by sliding the shank of the ball mount into the opening of the hitch and securing it with the pin and clip. more
9/25/2013 1:48:13 PM
Convert-A-Ball Ball Mount with 8 Inch Drop Review - 2013 Jeep Wrangler- Video
Today on our 2013 Jeep Wrangler, we'll be test fitting the convertible cushion ball mount for two inch hitches with a 6 3/4 inch rise, 2 1/8 inch drop, rated at 10,000 pounds, part number AMSC8. Before we begin our test fit, we'll first need to obtain the hitch height of our vehicle. This is the measurement from the ground to the inside top of the receiver tube. The hitch height for this vehicle is about 19 3/4 of an inch. Keep in mind that this measurement may very due to tire size, hitch style, or other aftermarket accessories. We'll begin our test fit by by sliding the shank of the ball mount in the drop position into the opening of the hitch, and securing it with a pin and clip. We can then measure from the ground to the top of the ball platform getting a measurement of about 11 3/4 of an inch. Now if your vehicle's hitch height matches ours, and your trailers ride height matches this measurement, this should be an appropriate ball mount for you. We can now flip the ball mount over to the rise position, and as you can see, the ball mount does come in contact with the spare tire, and prevents us from securing the ball mount with the pin and clip. more
9/25/2013 1:48:00 PM
Convert-A-Ball Ball Mount with 2 Inch Drop Review - 2013 Jeep Wrangler- Video
Today on our 2013 Jeep Wrangler we'll be test fitting the Convert-a-Ball cushion ball mount for 2-inch hitches with a 3/4-inch rise or 2-inch drop, rated at 10,000 pounds, part number AMSC2. Before we begin our test fit, we'll first need to obtain the hitch height of our vehicle. This is the measurement from the ground to the inside top of the receiver tube. The hitch height for this vehicle is about 19-3/4 inch. Keep in mind that this measurement may vary due to tire size, hitch style or other after market accessories. We'll begin our test fit in the drop position by sliding the shank of the ball mount into the opening of the hitch and securing it with a pin and clip. We can then measure from the ground to the top of the ball platform getting a measurement of about 18-1/4 inch. Now if your vehicle hitch height matches our's and your trailer ride height matches this measurement, this should be an appropriate ball mount for you. We can now flip the ball mount over into the rise position and again measure from the ground to the top of the ball platform. We'll get a measurement of about 20-1/2 inches. more
9/25/2013 1:47:47 PM
Convert-A-Ball Heavy Duty Ball Mount with 2 Inch Drop Review - 2013 Jeep Wrangler- Video
Today on our 2013 Jeep Wrangler, well be test fitting the Convert-A-Ball Cushion Ball Mount for 2 inch hitches with a 1 inch rise or a 2 inch drop, rated at 14,000 pounds, part number AMSC2HD. Before we begin our test fit, well first need to obtain the hitch height of our vehicle. This is the measurement from the ground to the inside top of the receiver tube. The hitch height for this vehicle is about 19-3/4 of an inch. Keep in mind that this measurement may vary due to tire size, hitch style or other aftermarket accessories. Well begin our test fit by sliding the shank of the ball mount into the opening of the hitch in the drop position and securing it with the pin and clip. We can then measure from the ground to the top of the ball platform getting a measurement of about 18 inches. more
9/25/2013 1:41:07 PM
Filter Videos
Filter Videos
